
Time-tested technology provides three-dimensional Vibro-Energy motion for all SWECO Finishing Mills. This motion subjects parts and media to a consistent high-frequency tilting movement as they travel in a helical/orbital path around the chamber. The resulting compressive scrubbing action cleans and also removes burrs, round sharp corners, and smooths out surface impressions. Because vertical/horizontal amplitudes and the rate of vibration are completely adjustable, your finishing requirements can be handled quickly and efficiently.

SWECO VIBRATORY TUMBLERS

Batch Mills

The Batch Series contain mills with capacities ranging from 1.2 to 20 cubic feet. That's 360 to 6,000 pounds of load capacity. These mills can process parts as large as 30 inches long. There is an open top for visual inspection or parts retrieval without stopping the process, and there is no transmitted vibration to the floor. Additionally, they have a higher capacity per horsepower than other types of vibrating units.
MODEL
CAPACITY
MOTOR
LINING
RESOURCES
FM-1.2C
1.2 ft³ (300 lbs. load capacity)
Max Straight Part Length :
9 inches
1/3 hp, TENV, 1200 RPM, single phase 115 volt; 3-phase 230, 460 or 575 volt. 60 Hz.
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FM-3C
3 ft³ (900 lbs. load capacity)
Max Straight Part Length :
12 inches
1 ¼ hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
5/16" HOT Cast Polyurethane Elastomer with curved outer wall
FM-3HA
3 ft³ (900 lbs. load capacity)
Max Straight Part Length :
12 inches
1 ¼ hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
5/16" HOT Cast Polyurethane Elastomer
FM-10V
10 ft³ (3000 lbs. load capacity)
Max Straight Part Length :
24 inches
5 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
¾" HOT Cast Polyurethane Elastomer
FM-10C
10 ft³ (3000 lbs. load capacity)
Max Straight Part Length :
24 inches
5 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
¾" HOT Cast Polyurethane Elastomer with curved outer wall
FM-20HA
20 ft³ (6000 lbs. load capacity)
Max Straight Part Length :
30 inches
10 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
¾" HOT Cast Polyurethane Elastomer with curved outer wall

Long Radius Mills

The Long Radius Series contain mills with capacities ranging from 1 to 24 cubic feet. That's 300 to 7,200 pounds of load capacity. These mills can process parts as large as 36 inches long. They also have special features for low noise operation and minimum vibration transfer to the floor. The series has an improved internal parts/media separation system that installs quickly for faster unloading.
MODEL
CAPACITY
MOTOR
LINING
RESOURCES
FMD-1LR
1 ft³ (300 lbs. load capacity)
Max Straight Part Length :
9 inches
1/3 hp, TENV, 1200 RPM, single phase 115 volt; 3-phase 230, 460 or 575 volt. 60 Hz. (non-reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-3LR
3 ft³ (900 lbs. load capacity)
Max Straight Part Length :
15 inches
1 ¼ or 2 ½ hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. (non-reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-4LR
4 ft³ (1200 lbs. load capacity)
Max Straight Part Length :
18 inches
2 ½ hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. (non-reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-7LR2
7 ft³ (2100 lbs. load capacity)
Max Straight Part Length :
20 inches
5 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. (non-reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-10LR
10 ft³ (2500 lbs. load capacity)
Max Straight Part Length :
24 inches
5 hp, TENV, 1200 RPM, 3-phase 230 or 460 volt. 60 Hz.
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-14LR
14 ft³ (4200 lbs. load capacity)
Max Straight Part Length :
24 inches
5 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. (reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas
FMD-24LR
24 ft³ (4200 lbs. load capacity)
Max Straight Part Length :
36 inches
10 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. (reversing)
Chamber - all HOT cast polyurethane elastomer with ¾" minimum thickness in high wear areas

Spiral Mills

The Spiral Series contain mills with capacities ranging from 5 to 20 cubic feet. That's 1,500 to 6,000 pounds of load capacity. These mills can process parts as large as 18 inches long. The Batch Series provides both batch automatic and continuous finishing, depending on the process requirements. They can process parts with all types of media, including steel burnishing shapes plus ceramic and plastic preforms.
MODEL
CAPACITY
MOTOR
LINING
RESOURCES
FMS-5LR
5 ft³ (1500 lbs. load capacity)
Max Straight Part Length :
12 inches
5 hp, TENV, 1200 RPM, 3-phase 230, 460 or 575 volt. 60 Hz.
Chamber - all cast polyurethane elastomer with 1" minimum thickness in high wear areas
FMS-14LR
14 ft³ (4200 lbs. load capacity)
Max Straight Part Length :
14 inches
10 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz.
Abrasion-resistant lining of cast polyurethane with ¾" minimum thickness in high wear areas.
FMS-20LR
20 ft³ (4200 lbs. load capacity)
Max Straight Part Length :
18 inches
20 hp, TENV, 1200 RPM, 3-phase 230, 460, or 575 volt. 60 Hz. Recirculating oil lubrication system.
Abrasion-resistant lining of cast polyurethane with 1" minimum thickness in high wear areas.

LOOKING FOR MORE RESOURCES?

CERTIFIED
FINISHING SERVICES
Our Sub-Contract finishing services are held to PPAP, ISO, FFL, MIL, SAE, and other tight industry standards. Our services include shot peening, vibratory finishing, industrial washing, accelerated surface finishing and more.

PROCESS
DEVELOPMENT
Our process development team will help diagnose your project or application at hand, bringing over 250+ years of combined industry experience. utilizing our finishing facilities, come experience first hand the process and equipment before delivery.

REPLACMENT
PARTS
If process control is critical to your operation, parts become an integral PM required to keep your process consitant and reliable. Check out our online store for quick selections and reliable delivery.